Glossy White Subway Tile SPC Wall Panels Bevel Edge Waterproof Kitchen and Bathroom Wall Cladding

Glossy White Subway Tile SPC Wall Panels

XINGJI glossy white subway tile SPC wall panels carry the brick-bond metro tile look on a single waterproof board. Each tile face is 300 x 75 mm with a chamfered bevel, offset half a tile row to row, and the joints are formed in the surface rather than filled with grout, so a splashback is finished as a panel instead of a tiling job.

The board is a stone-plastic composite: a rigid waterproof core under a printed decor layer and a UV-cured wear layer. That means no adhesive bed, no grout lines to scrub, no substrate swelling behind the tiles, and a surface that wipes clean in one pass. It is the practical choice where a client wants the subway look but not the maintenance or the drying time.

Panels come 600 mm and 1200 mm wide and 4 mm thick, interlock tongue-and-groove, and fix glue-free over a flat existing wall, including sound tiling. Standard widths ship from stock, with cut-to-size lengths and OEM packing to order.

Key Features

• 300 x 75 mm bevel-edge tile faces laid in true brick bond
• Glossy white glaze look with subtle per-tile tone variation
• No grout: joints are formed in the surface and wipe clean
• Waterproof SPC core, no added formaldehyde
• Fixes glue-free over flat walls, including sound tiling
• UV-cured wear layer for kitchens and bathrooms
• 600 mm and 1200 mm widths, 4 mm thick, approx. 1.97 kg/m2
• Matching end caps and corner trims available

Specifications

Where It Is Used

• Kitchen splashback behind hob and sink
• Bathroom vanity and half-height wall cladding
• Cafe and bakery service counter fronts
• Utility and laundry room walls
• Salon and clinic washable wall surfaces
• Retail back-of-counter panels

Installation, Step by Step

SPC Subway Panel vs Ceramic Subway Tiles

Care and Maintenance

• Wipe with a damp cloth and a pH-neutral kitchen cleaner.
• Avoid abrasive cream cleaners and scouring pads on the gloss face.
• No grout to re-seal and no mould to treat in the joint lines.
• Use a silicone bead at worktop junctions rather than grout.

Packing and Loading

FAQ

1. Are these real tiles or a printed pattern?
A printed and wear-protected decor on a rigid SPC board. The tile joints are formed in the surface, so the brick bond reads correctly under raking light, but nothing is grouted.

2. Can it go directly behind a hob?
Yes, as a splashback face. Keep the recommended clearance to the hob and seal the junction with a heat-resistant silicone where the appliance manufacturer requires it.

3. Can I install it over my old tiles?
Yes, if the existing tiles are sound and the surface is flat. Fill the joint lines flush first so the new board sits without rocking.

4. How do the joints stay clean without grout?
The joint is a shallow formed channel in a non-porous surface, so grease and soap residue wipe out with a cloth. There is no porous grout line to absorb dirt.

5. Is the gloss slippery when wet?
The board is a wall product and is not intended as a floor surface, so slip resistance does not apply to its normal use.

6. What happens at an external corner?
Fit a matching corner trim, or mitre the two boards and close the edge with a colour-matched sealant.

7. Do you supply the trims in the same finish?
End caps, internal and external corners and skirting profiles are available in the same decor for project orders.

8. Can the tile size be changed?
The 300 x 75 mm brick bond is the standard layout. Other tile sizes and bond patterns can be produced to order for project volumes.

Why XINGJI

XINGJI has produced stone-plastic wall panels since 2016, with printing, wear-layer lamination, profiling and packing under one roof. Orders are quoted with decor, tile layout, width and packing confirmed in writing before production, and OEM/ODM work is supported from sample to container.